Chemistry, Physics and Technology of Surface

ISSN 2518-1238 (Online), ISSN 2079-1704 (Print)

To create film materials with antimicrobial properties, silver nanoparticles are widely used, which are introduced, in particular, into polymer matrices. In this work, a mixture of polylactide-polycaprolactone polymers, taken in a mass ratio of 80–20, was used as a polymer base. These studies will further contribute to the development of new safe materials, particularly in creating packaging materials for food products, which is undoubtedly an urgent problem today.

The work aimed to create silver-containing polymer composites based on a mixture of polylactide and polycaprolactone by vacuum deposition of silver nanoparticles on the surface of the polymer matrix and to study the structure, morphology, thermophysical, antimicrobial, and genotoxic properties of the obtained composites.

Silver nanoparticles were sputtered on the surface of the PLA-PCL polymer mixture using an FC-1100 ion sputtering device (JEOL, Japan) for 1, 3, and 5 min. The thickness of the films was 110 μm. The structure, morphology, thermophysical, antimicrobial, and genotoxic properties of composites formed by sputtering silver nanoparticles on the surface of the polymer were studied using wide-angle X-ray scattering on a device XRD-7000 (Shimadzu, Japan), transmission electron microscopy (TEM) (a JEM-1230 JEOL, Japan), thermogravimetric analysis (a TGA Q50) (TA Instruments, USA), differential scanning calorimetry (a DSC Q2000) (TA Instruments, USA), as well as antimicrobial and genotoxic tests.

Using X-ray structural analysis, it was found that the original polymers are characterized by a semi-crystalline structure, and the presence of metallic silver on the surface of the polymer was confirmed. It is shown that a layer of silver particles of about 425 nm is formed on the surface of the PLA-PCL mixture for a sputtering duration of 5 minutes.

According to the results of differential scanning calorimetry, it has been found that when sputtering silver particles on the surface of polymers, the degree of crystallinity increases from 35 to 39 %, and the melting temperature T_m increases from 168 to 169–170 °C. At the same time, the influence of the metallic layer of silver on the amorphous phase of the polymer was not recorded.

The antimicrobial activity of PLA-PCL-Ag samples with a spraying duration of 3 and 5 min against S. aureus and E. coli microorganisms was revealed.

It was found that the studied samples did not show a toxic effect.

1. Demchenko V.L., Shtompel V.I. Structuring, Morphology, and Thermomechanical Properties of Nanocomposites Formed from Ternary Polyelectrolyte-Metal Complexes Based on Pectin, Polyethyleneimine, and CuSO4. Polym. Sci. Ser. B. 2014. 56: 927. https://doi.org/10.1134/S1560090414060049

2. Demchenko V.L., Shtompel V.I., Riabov S.V. DC Field Effect on the Structuring and Thermomechanical and Electric Properties of Nanocomposites Formed from Pectin-Cu2+-Polyethyleneimine Ternary Polyelectrolyte-Metal Complexes. Polym. Sci. Ser. A. 2015. 57: 635. https://doi.org/10.1134/S0965545X15050065

3. Pavoski G., Kalikoski R., Souza G., Brum L.F.W., dos Santos C., Markeb A.A., dos Santos J.H.Z., Font X., Dell'erba I., Galland G.B. Synthesis of polyethylene/silica-silver nanocomposites with antibacterial properties byin situ polymerization. Eur. Polym. J. 2018. 106: 92. https://doi.org/10.1016/j.eurpolymj.2018.07.011

4. Oliveira M.M., Ugarte D., Zanchet D., Zarbin A.J. Influence of synthetic parameters on the size, structure, and stability of dodecanethiol-stabilized silver nanoparticles. J. Colloid Interface Sci. 2005. 292(2): 429. https://doi.org/10.1016/j.jcis.2005.05.068

5. Rakowska P.D., Tiddia M., Faruqui N., Bankier C., Pei Y., Pollard A.J., Zhang J., Gilmore I.S. Antiviral surfaces and coatings and their mechanisms of action. Commun. Mater. 2021. 2: 53. https://doi.org/10.1038/s43246-021-00153-y

6. Li J., Zhuang S. Antibacterial activity of chitosan and its derivatives and their interaction mechanism with bacteria: current state and perspectives. Eur. Polym. J. 2020. 138: 109984. https://doi.org/10.1016/j.eurpolymj.2020.109984

7. Abbas M., Buntinx M., Deferme W., Peeters R. (Bio)polymer/ZnO Nanocomposites for Packaging Applications: A Review of Gas Barrier and Mechanical Properties. Nanomaterials. 2019. 9(10): 1494. https://doi.org/10.3390/nano9101494

8. Li G., Zhao M., Xu F., Yang B., Li X., Meng X., Teng L., Sun F., Li Y. Synthesis and Biological Application of Polylactic Acid. Molecules. 2020. 25(21): 5023. https://doi.org/10.3390/molecules25215023

9. Singhvi M.S., Zinjarde S.S., Gokhale D.V. Polylactic acid: synthesis and biomedical applications. J. Appl. Microbiol. 2019. 127(6): 1612. https://doi.org/10.1111/jam.14290

10. Sikorska W., Zięba M., Musioł M., Kowalczuk M., Janeczek H., Chaber P., Masiuchok O., Demchenko V., Talanyuk V., Iurzhenko M., Puskas J.E., Adamus G. Forensic Engineering of Advanced Polymeric Materials-Part VII: Degradation of Biopolymer Welded Joints. Polymers. 2020. 12(5): 1167. https://doi.org/10.3390/polym12051167

11. Masiuchok O., Iurzhenko M., Kolisnyk R., Mamunya Y., Godzierz M., Demchenko V., Yermolenko D., Shadrin A. Polylactide/carbon black segregated composites for 3D printing of conductive products. Polymers. 2022. 14(19): 4022. https://doi.org/10.3390/polym14194022

12. Beltrán F.R., Arrieta M.P., Moreno E., Gaspar G., Muneta L.M., Carrasco-Gallego R., Yáñez S., Hidalgo-Carvajal D., de la Orden María U., Urreaga J.M. Evaluation of the Technical Viability of Distributed Mechanical Recycling of PLA 3D Printing Wastes. Polymers. 2021. 13(8): 1247. https://doi.org/10.3390/polym13081247

13. Nootsuwan N., Sukthavorn K., Wattanathana W., Jongrungruangchok S., Veranitisagul C., Koonsaeng N., Laobuthee A. Development of Antimicrobial Hybrid Materials from Polylactic Acid and Nano-silver Coated Chitosan. Orient. J. Chem. 2018. 34(2): 683. https://doi.org/10.13005/ojc/340210

14. Velgosova O., Mačák L., Lisnichuk M., Vojtko M. Synthesis and Analysis of Polymorphic Silver Nanoparticles and Their Incorporation into the Polymer Matrix. Polymers. 2022. 14(13): 2666. https://doi.org/10.3390/polym14132666

15. García B.O., Kharissova O.V., Dias R., Aguirre-Tostado F.S., Leyva C., González L.T., Kharisov B.I. A Comparison of Different Methods of MWCNTs Metalation in a Single Step Using Three Different Silver-containing Compounds. Recent Pat. Nanotechnol. 2019. 13(1): 59. https://doi.org/10.2174/1872210513666190225095537

16. Tatarchuk V.V., Sergievskaya A.P., Korda T.M., Druzhinina I.A., Zaikovsky V.I. Kinetic Factors in the Synthesis of Silver Nanoparticles by Reduction of Ag+ with Hydrazine in Reverse Micelles of Triton N-42. Chem. Mater. 2013. 25(18): 3570. https://doi.org/10.1021/cm304115j

17. Gupta A., Briffa S.M., Swingler S., Gibson H., Kannappan V., Adamus G., Kowalczuk M., Martin C., Radecka I. Synthesis of Silver Nanoparticles Using Curcumin-Cyclodextrins Loaded into Bacterial Cellulose-Based Hydrogels for Wound Dressing Applications. Biomacromolecules. 2020. 21(5): 1802. https://doi.org/10.1021/acs.biomac.9b01724

18. Clinical and Laboratory Standards Institute NCCLS. Performance standards for antimicrobial susceptibility testing; fifteenths informatonal supplement. CLSI/NCCLS document M100-S15. Clinical and Laboratory Standards Institute. Wayne. PA. 2005.

19. Brouillard J.E., Terriff C.M., Tofan A., Garrison M.W. Antibiotic selection and resistance issues with fluoroquinolones and doxycycline against bioterrorism agents. Pharmacotherapy. 2006. 26(1): 3. https://doi.org/10.1592/phco.2006.26.1.3

20. Rodriguez-Garraus A., Azqueta A., Vettorazzi A., López de Cerain A. Genotoxicity of Silver Nanoparticles. Nanomaterials. 2020. 10(2): 251. https://doi.org/10.3390/nano10020251

21. Shtompel' V.I., Kercha Yu.Yu. Structure of Linear Polyurethanes. (Kiyv: Naukova dumka, 2008). [in Russian].

22. Borukaev T.A., Shaov A.Kh., Kharaev A.M., Borodulin A.S. Influence of the compatibilizer on the properties of composites based on low density polyethylene and polybutylene terephthalate. E3S Web of Conferences. 2023. 413: 1. https://doi.org/10.1051/e3sconf/202341302037

23. Körber S., Moser K., Diemert J. Development of high temperature resistant stereocomplex PLA for injection moulding. Polymers. 2022. 14(3): 384. https://doi.org/10.3390/polym14030384